Hot Dipped Multislot Diffuser standards

Product NameHot Dipped Multislot Diffuser standards
MaterialPlastic,ABS,PVC or other material
ColorWhite or custom color
StandardChina standard
SizeCustomized
MOQ10
PackagingStandard packaging
Delivery30day
  • Electrical Design.pdf | Power Supply | Power (Physics)

    Standard specifications, etc. defines the requirements for design, engineering, supply and,Thickness of hot dip galvanizing shall be minimum 700gm/m2. Specifically provided bolts, lugs and spring washers shall be used for all earthing connections of equipment.

    Ask For Quote Details
  • 4 Technical Specs Towers HVAC | Specification (Technical

    Fan motor shall be single phase 220 + 6% or three phase 415 ± 10% volts, 50 hertz, energy. efficient (IE-2), totally enclosed fan-cooled, Class F insulation and IP-55 protected. Motor speed. shall not exceed 1440 rpm for forward curved fan and 2900 rpm for backward curved fans with oil-.

    Ask For Quote Details
  • Minimum Technical Requirements (Indice Delle Norme Da

    In the open air, in plant rooms and in large unconditioned open areas of buildings, the. thermal insulation shall be at least 50 mm thick where the thermal conductivity is less than or equal to. 0.04 W/m o C or at least 63 mm thick where the thermal conductivity is between 0.04 and 0.06 W/m o. C. Page 125 of 183.

    Ask For Quote Details
  • Specification Bank Building | Concrete | Sand

    SECTION - F ( PART -I) MASONRY - BRICK WORK 1.0 Indian Standards to be followed are : All relevant Standards as specified elsewhere in this Volume are applicable. Indian Standards to be followed are : 1. IS 226 Specification for steel standard quality. 2. IS 269 Specification for ordinary and low heat Portland cement. 3.

    Ask For Quote Details
  • Construction Of Bank Square Building At Ambala Can Tender

    Supply, installation, testing and balancing of square, air diffusers. All diffusers must be multislotted complete with air pattern controller. Each diffuser shall be equipped with fixed air distribution grid and antis-mudge ring where required as per the shop drawings & specifications. 426: 235.01: Extruded Aluminium powder coated diffusers

    Ask For Quote Details
  • Electrical Design | Cable | Specification (Technical Standard)

    Thickness of hot dip galvanizing shall be minimum 700gm/m2. Specifically provided bolts, lugs and spring washers shall be used for all earthing connections of equipment. Following sizes of earth conductors shall be used for motors: Upto 3.7 KW 85WG GI wire 5.5 to 30 KW3/8" GI fine wire rope or 35mm2 AI insulated conductor 37 to 75 KW 5/8" GI

    Ask For Quote Details
  • Total

    Virtually all PGBs utilize the API standard post spacing, four guideposts at 90 spacing, on a six-foot radius from the well center. This leads to the standard 101.82 inches between posts. Figure 2.7 - Example of a Retrievable Permanent Guide Base PGBs can be designed to be retrievable while leaving the well intact for future use.

    Ask For Quote Details
  • Registers Grilles and Diffusers | Auer Steel

    Hart & Cooley® 210 09 12 GS Heavy Duty Floor Register, 9 x 12 in, 180 to 600 cfm, Steel, Golden Sand Enamel, Domestic. Brand Name: Hart & Cooley®. Manufacturer Name: Hart & Cooley. MPN: 210 09 12 GS.

    Ask For Quote Details
  • FCB741 – FC Lighting

    Impact resistant, UV stabilized, clear, polycarbonate diffuser. Neoprene continuous closed cell gasket to seal out contaminants. Captive and recessed stainless steel, tamper resistant hex socket screws. A thick die-cast base plate is provided and anchored through with a set of three 12″ length x 3/8″ diameter hot dipped anchor bolts.

    Ask For Quote Details


Our Location

Contact Us

Boda Aluminum Products Co.,LTD

Address: Jingjiang, Taizhou City
Jiangsu Province, China
Zip code - 214500
Telephone: +86 18262317598
E-mail: [email protected]